Write 7 pages thesis on the topic isentropic expansion of ideal gas.

/in /by

Write 7 pages thesis on the topic isentropic expansion of ideal gas. By recording and using relevant pressure measurements with the help of suitable pressure gauges. The value of the specific heat capacity of air could be calculated. A relatively low percentage error in the readings and average value very close to the expected value (precision value) led to the conclusion that the experiment and the simulated adiabatic expansions were quite precise and reliable.

The specific heat (C) is critical because it determines how quickly a substance will heat up or cool down. It is a quantity of heat that is required to change the temperature of 1 kilogram of a substance by 1 degree Celsius. Specific heat capacity is a quantity central to the thermodynamic analysis of a substance.

In this experiment, the pressure was the best parameter to monitor and evaluate, and thus an equation relating the specific heat and the two pressure readings had to be derived. The derivation required the application of the first law of thermodynamics to the adiabatic expansion process and using the ideal gas law, making an assumption that the air behaves like an ideal gas.

In thermodynamics, an isentropic process is a process that takes place from initiation to completion without an increment or decrement in the entropy of the system. In other words, the entropy of the system remains constant. Entropy is a form of energy.

If a process is both reversible and adiabatic, then it is an isentropic process. An isentropic process is an idealization of an actual process and serves as a limiting case for an actual process. For an adiabatic process, there is no transfer of heat energy.

Before the experiment, the atmospheric pressure, P2 was measured using the barometer so as to determine the absolute pressures of the cylinder. In a similar way, the room temperature T1 was measured using the mercury in a glass thermometer.

The vessel was gradually pressurized to 5psig and the air supply turned off followed by the closing of the valve in order to isolate the compressed air inside the tank.&nbsp.

people and organization management in the built environment

/in /by

I need some assistance with these assignment. people and organization management in the built environment Thank you in advance for the help! Change is indeed the one and only constant that exists within organizations. It is imperative to state that change is rampant because it makes things look easier from the long term perspectives. It makes the top management feel glad about their actions after the change philosophy has been defined, executed, and implemented to seek the best possible results for the sake of the organizations.

Within this paper, the focus would be kept on the built environment as change is witnessed at different levels so as to apprise all and sundry regarding the issues and concerns that the middle management and the lower staff have from time to time. It will also study the basis of change as a general proposition and then go on to find alternate routes in order to discern how change has been seen over the years in diverse industries and how it will be constantly viewed in the coming times as well. With that, a proper understanding of the change principles will be sought which shall tackle the nuances related to how people see change as a catalyst towards creating something big and gigantic within organizations. The role of the employees and the top management is also crucial towards forming such opinions and they will rightfully be given an opportunity to have their viewpoints expressed.&nbsp.

To begin the discussion at hand, it is quintessential to know where change can be incorporated within an organization. What this basically does is to tell the people at large how change is being seen and where its maximum uses and benefits can be drawn. It also tells the audience that change is the only element that shall remain constant at the best of times and must not be disallowed under any situation whatsoever. It only helps the processes become more focused and rationalized, allowing the people involved within it at different levels a greater mileage than ever before. However, not many businesses understand this principle as it should be (Berkowitz, 1993).&nbsp.&nbsp.

Planting a Tree. The work is to be 3 pages with three to five sources, with in-text citations and a reference page.

/in /by

I will pay for the following article Planting a Tree. The work is to be 3 pages with three to five sources, with in-text citations and a reference page.

1. Identifying which tree you want to plant is the first step in this regard. Clearly define which tree you want to plant and what your purpose of planting the tree is. If you are planting a tree just for the purpose of planting, your choice may differ. However, if you are planting the tree so that you can grow it and eat its fruit your overall effort may be different. It is therefore extremely important to define the purpose for which the tree is being planted.2. Selecting the right time of the year is another important step because not all trees can be planted in every season.

Planting trees in summer or late spring may not be suitable as the heat may not allow the plant to grow properly and may ultimately die down. It is critical that the right time of the year must be chosen to plan the tree. 3. Digging the hole in the right size and width is another important step to be performed in order to successfully plant the tree. Many times, people dig holes that are either large or wider and thus may not be suitable for the planting of the tree. One can learn from the intuition as to what should be the right width and depth of the hole considering the size of the tree being planted.

A typical standard to dig the hole of the right size is to dig it at least twice as large as the root ball of the tree. You may also need to check the local requirements for digging the hole of the right size especially if you are digging it near a telephone booth or other public places. There may be certain restrictions on digging the hole over the particular size in local areas so better check with the local requirements. 4. Once the hole is dug, the next step is to place the tree in the hole in a manner that it can easily fit the tree inside the hole.

The overall process to place the tree in the hole is, however, different for large and small trees. If you are planting a small tree, it is easier to upside down the pot and removes the tree to plant it. However, if the tree is large, you may require a large scissor or knife to actually cut through the packing and then place the tree in the hole of the right size. Sometimes, large trees have ropes around their trunk therefore if you find one. try to cut it after you actually place the tree in the hole.

Once you unpack the tree, try to place the tree gently and ensure that the hole is wide enough to accommodate the tree. At this moment, it is extremely important to ensure that the hole is not shallow neither is deep and then gently places the tree.5. Once you place the tree in the hole, it is important to cover back the hole with the soil removed while digging the hole. Sometimes, the soil may not be suitable therefore you may require some composted manure to fill the hole. Composted manure will actually further fertile the soil and will also make it soft so that enough water can reach the roots of the tree.

Make sure that you have composted readily available at the time of planting the tree.6. Make sure that you use the proper organic fertilizer for the tree to grow as commercial fertilizer may burn the tree. Once you cover the hole with the soil and manure, the use of good quality fertilizer is essential to help the tree to grow easily.7. Continue to water the plant and ensure that the plant gets adequate sunlight, water, and fertilizer to grow. Planting tree is a lifelong process therefore continues to take care of your tree till gives the fruit and increases your efforts to get more fruit by properly watering the plant.

After completing any project, it is important to conduct a review of the project to ensure that all activities have been completed and delivered in scope. Reviews also help gather lessons learned for future project managers. Remember that a project is temporary in that it has a defined beginning and end, with a defined scope. It is unique in that it is not a routine operation, but a specific set of operations designed to accomplish a single goal. For example, your involvement in this course can be viewed as a project: it has a definite beginning and end, it has a defined scope (the syllabus), and it is designed to accomplish a single goal (to provide you with an overview of project management). Your final assignment for this course will be to conduct a project evaluation as part of its closeout. You are to create a PowerPoint presentation of at least 9 slides. In your presentation, you will perform a review of this course (the course represents the project, and the course syllabus represents the project plan). Your presentation should apply closeout best practices and should capture lessons learned. You may use any checklists and templates from your text or find them online. You are free to be creative with this assignment. Be sure to cite your sources (if applicable) using APA. Include your references and in-text citations. Submitting your assignment in APA format means, at a minimum, you will need the following: Title slide: Remember the running head. The title should be in all capitals. Length: 9 slides minimum Body slides: This begins on the slide following the title slide and must be double-spaced (be careful not to triple- or quadruple-space between paragraphs). The typeface should be 12-pt. Times Roman or 12-pt. Courier in regular black type. Do not use color, bold type, or italics, except as required for APA-level headings and references. The deliverable length of the body of your presentation for this assignment is 8 slides. In-body academic citations to support your decisions and analysis are required. A variety of academic sources is encouraged. Reference slide: References that align with your in-body academic sources are listed on the final slide of your presentation. The references must be in APA format using appropriate spacing, hanging indent, italics, and uppercase and lowercase usage as appropriate for the type of resource used. Remember, the Reference slide is not a bibliography but a further listing of the abbreviated in-body citations used in the paper. Every referenced item must have a corresponding in-body citation.

/in /by

After completing any project, it is important to conduct a review of the project to ensure that all activities have been completed and delivered in scope. Reviews also help gather lessons learned for future project managers.

Remember that a project is temporary in that it has a defined beginning and end, with a defined scope. It is unique in that it is not a routine operation, but a specific set of operations designed to accomplish a single goal. For example, your involvement in this course can be viewed as a project: it has a definite beginning and end, it has a defined scope (the syllabus), and it is designed to accomplish a single goal (to provide you with an overview of project management).

Your final assignment for this course will be to conduct a project evaluation as part of its closeout. You are to create a PowerPoint presentation of at least 9 slides. In your presentation, you will perform a review of this course (the course represents the project, and the course syllabus represents the project plan). Your presentation should apply closeout best practices and should capture lessons learned.

You may use any checklists and templates from your text or find them online. You are free to be creative with this assignment. Be sure to cite your sources (if applicable) using APA. Include your references and in-text citations.

Submitting your assignment in APA format means, at a minimum, you will need the following:

  • Title slide: Remember the running head. The title should be in all capitals.
  • Length: 9 slides minimum
  • Body slides: This begins on the slide following the title slide and must be double-spaced (be careful not to triple- or quadruple-space between paragraphs). The typeface should be 12-pt. Times Roman or 12-pt. Courier in regular black type. Do not use color, bold type, or italics, except as required for APA-level headings and references. The deliverable length of the body of your presentation for this assignment is 8 slides. In-body academic citations to support your decisions and analysis are required. A variety of academic sources is encouraged.
  • Reference slide: References that align with your in-body academic sources are listed on the final slide of your presentation. The references must be in APA format using appropriate spacing, hanging indent, italics, and uppercase and lowercase usage as appropriate for the type of resource used. Remember, the Reference slide is not a bibliography but a further listing of the abbreviated in-body citations used in the paper. Every referenced item must have a corresponding in-body citation.